Numerical Simulation of the Electric Field and Potential Distribution Analysis in a 20 kV Polymeric Insulator Under the Influence of Mechanical Defects and Various Non-Uniform Pollution Patterns

Ghorbani Pashakolaei, Mehrdad; Jazaeri, Mostafa; Niasati, Mohsen; Seyed Barzegar, Seyed Meysam

doi:10.22075/jme.2025.37088.2825

Numerical Simulation of the Electric Field and Potential Distribution Analysis in a 20 kV Polymeric Insulator Under the Influence of Mechanical Defects and Various Non-Uniform Pollution Patterns

Document Type : Research Paper

Authors

Mehrdad Ghorbani Pashakolaei ¹

Mostafa Jazaeri ¹

Mohsen Niasati ¹

Seyed Meysam Seyed Barzegar ²

¹ Faculty of Electrical and Computer Engineering, Semnan University, Semnan, Iran

² Department of Robotic and Electrical Engineering, Shahrood University of Technology, Shahrood, Iran

10.22075/jme.2025.37088.2825

Abstract

The presence of non-uniform pollution deposits on the surface of insulators, along with mechanical defects, significantly affects the performance of overhead line insulators. However until now, no comprehensive studies have been conducted on the simultaneous effect of different types of non-uniform pollution and mechanical defects on insulator performance. In this paper the effects of uniform and non-uniform pollution, including the ring-shaped (RNU) and ring-longitudinal (RLNU) types, along with mechanical defects such as a damaged shed and a defective core, on the potential distribution and electric field of a 20 kV polymeric insulator have been investigated. The simulations were performed using COMSOL Multiphysics and the results were analyzed. In the case of longitudinal non-uniform pollution, the pollution severity was assumed to be heavy in the regions near the electrodes and light in the middle region. Additionally for the ring-shaped non-uniform pollution the inner and outer areas were assumed to be equal with pollution applied to the inner region of the insulator. The results indicate that the maximum electric field in the uniform pollution condition is higher than in other pollution patterns. Moreover the presence of mechanical defects, such as damage to the shed and core, has a significant impact on the potential distribution and the maximum electric field. Specifically compared to a healthy insulator the presence of these defects leads to an increase in the maximum electric field in three regions: the high-voltage region the middle region, and the low-voltage region.

Keywords

Polymeric insulator

Electric potential distribution

Electric field Distribution

Mechanical defects

Non-uniformpollution

FEM analysis

Subjects

مهندسی برق قدرت

[1] Li, W., and Y. Zhang. “Comparison of dielectric properties of polymeric materials in high-voltage applications.” Journal of Electrical Engineering 76, no. 3 (2024): 211–220.

[2] Murugan, R., and C. Abinaya. “Performance analysis of polymer insulators under polluted conditions.” IEEE Transactions on Power Delivery 32, no. 2 (2023): 577–585.

[3] Chandrasekar, S., and R. Gorur. “Performance of silicone rubber and EPDM in high-voltage insulators.” IEEE Transactions on Dielectrics and Electrical Insulation 23, no. 6 (2023): 3441–3449.

[4] Shah, S. R., and K. Mehta. “Effects of UV exposure on polymer insulators: A review.” Polymer Testing 42 (2022): 206–215.

[5] Zhu, X., and W. He. “Analysis of corona aging in silicone rubber insulators.” IEEE Transactions on Dielectrics and Electrical Insulation 19, no. 6 (2020): 2178–2185.

[6] Kim, J. H., and H. K. Park. “Thermal aging effects on silicone rubber for outdoor insulators.” Journal of Thermal Analysis and Calorimetry 116, no. 3 (2021): 1537–1545.

[7] Zhang, Z., J. You, D. Zhang, X. Jiang, J. Hu, and W. Zhang. “AC flashover performance of various types of insulators under fan-shaped non-uniform pollution.” IEEE Transactions on Dielectrics and Electrical Insulation 23, no. 3 (2016): 1760–1768.

[8] Zhang, Z., D. Wei, D. Zhang, X. Jiang, and Y. Li. “Effects of ring-shaped non-uniform pollution on outdoor insulation electrical property.” IEEE Transactions on Dielectrics and Electrical Insulation 24, no. 6 (2017): 3603–3611.

[9] Tanaka, T., and G. C. Montanari. “Polymer nanocomposites as dielectrics and electrical insulation.” IEEE Transactions on Dielectrics and Electrical Insulation 18, no. 5 (2020): 1482–1517.

[10] Abbasi Chahardah Cheriki, Y., H. Farzin, and E. Mashhour. “Investigating the flashover probability of transmission network insulators during dust storms.” Journal of Applied Research in Electrical Engineering (2025).

[11] George, G., and M. J. Thomas. “Studies on tracking resistance of polymeric outdoor insulators.” IEEE Transactions on Dielectrics and Electrical Insulation 17, no. 3 (2020): 899–906.

[12] Cui, X., and X. Liang. “UV resistance of silicone rubber and EPDM in high-voltage insulators.” Journal of Applied Polymer Science 112, no. 6 (2020): 3245–3252.

[13] Roy, M., and J. K. Nelson. “Nanodielectrics: A review of materials and applications in HV insulation.” IEEE Electrical Insulation Magazine 24, no. 4 (2021): 20–30.

[14] Ma, G., and W. Li. “Influence of filler type on thermal properties of silicone rubber insulators.” Polymer Engineering & Science 47, no. 12 (2022): 2119–2125.

[15] Kuffel, E., J. Kuffel, and W. S. Zaengl. High Voltage Engineering: Fundamentals. 2nd ed. Butterworth-Heinemann, 2020.

[16] Krivda, A., P. Freimann, M. Götz, S. Moser, and H. Singer. “Aging of polymeric insulators under natural environmental conditions.” IEEE Transactions on Dielectrics and Electrical Insulation 12, no. 2 (2005): 327–342.

[17] Gorur, R. S., E. A. Cherney, and R. Hackam. “The effects of ultraviolet radiation on polymeric outdoor insulators.” IEEE Transactions on Power Delivery 5, no. 4 (2021): 1883–1890.

[18] Hackam, R. “Outdoor HV composite polymeric insulators.” IEEE Transactions on Dielectrics and Electrical Insulation 6, no. 5 (2020): 557–585.

[19] Vaswani, A. V., and R. S. Gorur. “Effect of water droplets on the flashover voltage of polymeric insulators.” IEEE Transactions on Dielectrics and Electrical Insulation 2, no. 6 (2021): 1032–1041.

[20] Ghiasi, Z., et al. “FEM analysis of electric field distribution for polymeric insulator under different configuration of non-uniform pollution.” Electrical Engineering (2021): 1–10.

[21] Asgari, M., and A. Gholami. “Analysis of electric field distribution in polymeric insulators under icing conditions using the finite element method.” Journal of Electrical Engineering, Tabriz University 44, no. 4 (2014): 47–54. (in Persian)

[22] De La O, J. A., and E. I. Ortiz-Rivera. “Impact of non-uniform pollution on insulator performance under DC voltage.” IEEE Power Engineering Review 25, no. 6 (2021): 67–69.

[23] Farzaneh, M., and W. A. Chisholm. Insulators for Icing and Polluted Environments. Wiley-IEEE Press, 2021.

[24] Ouchen, L., A. Haddad, S. Mekhilef, and A. Boudghene Stambouli. “A finite element with statistical analysis study to investigate the electrical performance of composite insulators under water droplet impact.” Scientific Reports 15, no. 1 (2025): 7364.

[25] Ghosh, M. A. “Effects of water droplets on the electrical properties of polymer insulators under high voltage.” IEEE Transactions on Dielectrics and Electrical Insulation 27, no. 1 (2022): 56–65.

[26] Kumar, P., R. K. Ghosh, and S. K. Gupta. “Impact of pollution severity on the electric field distribution in high-voltage insulators.” IEEE Transactions on Power Delivery 35, no. 3 (2023): 1704–1712.

[27] Patel, S., H. S. Prakash, and A. Jain. “Modeling the effect of artificial pollution on polymeric insulators: A finite element approach.” IEEE Transactions on Power Delivery 36, no. 4 (2023): 2243–2251.

[28] Salhi, R., A. Mekhaldi, M. Teguar, and O. Kherif. “Simulation and experimental analysis of electrical characterization of cap-pin glass insulator under uniform and non-uniform pollution layers.” Periodica Polytechnica Electrical Engineering and Computer Science 68, no. 4 (2024): 381–391.

[29] Dadashizadeh Samakoush, J., and M. Mirzaei. “Simulation and analysis of the effect of uniform and non-uniform (longitudinal and sectional) pollution on the potential and electric field distribution of polymer insulators using the finite element method.” Journal of Modeling in Engineering 17, no. 56 (2020): 1–12. (in Persian)

[30] Kone, G., C. Volat, and H. Ezzaidi. “Numerical investigation of electric field distortion induced by internal defects in composite insulators.” High Voltage 2, no. 4 (2017): 253–260.

[31] Fasani, D., R. Tallarida, C. Medrano, and M. Rossi. “Diagnostics of internal defects in composite overhead insulators using an optic E-field sensor.” Sensors 24, no. 5 (2024): 1359.

[32] Volat, C., et al. “New method for in live-line detection of small defects in composite insulator based on electro-optic E-field sensor.” IEEE Transactions on Dielectrics and Electrical Insulation 20, no. 1 (2013): 94–101.

[33] Cheng, L., et al. “An optimized infrared detection strategy for defective composite insulators according to the law of heat flux propagation considering the environmental factors.” IEEE Access 6 (2018): 38137–38146.

[34] Chandrasekar, S., P. Kalaivanan, A. Cavallini, and G. C. Montanari. “Understanding the impact of surface degradation and mechanical damage on ceramic insulators under electrical stress.” IEEE Transactions on Dielectrics and Electrical Insulation 22, no. 1 (2015): 456–464.