Journal of Modeling in Engineering

Journal of Modeling in Engineering

Investigating the Performance of a Car Catalyst Cooling Converter Equipped with an Electromechanical Temperature Control System

Document Type : Research Paper

Authors
1 Department Of Mechanical Engineering,Technical and Vocational University (TVU),Tehran, Iran
2 Department of Materials and Manufacturing Engineering, University of Mohaghegh Ardabili, Ardabil, Iran
3 Department of Mechanical Engineering, University of Mohaghegh Ardabili, Ardabil, Iran
Abstract
Controlling the temperature of the car catalyst is one of the effective factors in improving the efficiency of this part. The internal structure of the catalyst must be placed under certain thermal condition for optimally converting of exhaust gases. The theoretical and experimental results show that the internal structure of the catalyst in the temperature range of 300 °C to 600 °C has the greatest effect on greenhouse gases conversion. In this research, a theoretical solution has been proposed to prevent the deviation of the catalyst temperature from the defined limits. In order to prevent the raisin up the temperature of the catalyst, a double-walled converter with an asymmetric flow has been used. This part is installed before the car catalyst. The exhaust gases pass through it and then enter the catalyst. The cooler designed with four different lengths of 0.5m, 1m, 1.5m and 2m. the performance of the design is investigated numerically using a commercial finite volume code. The state of heat transfer and its effect on the gaeses temperature reduction has been evaluated. According to the results,the 0.5m in length cooler reduced the temperature to 291.6°C. By selecting the temperature reducing converter and automatically activating the fluid circulation operation at the critical temperature, the performance of the electromechanical system derived from sensors and actuators have been investigated.
Keywords
Subjects

[1] Jena, S., and M. Padhy. “The Environment and Catalytic Converter—A Review.” Materials International 7, no. 1 (2025): 1–21.
[2] Dadgar, Arsalan, Afsaneh Maleki, Leila Mahdavian, and Fereydoon Khazali. "Computational Investigation of the Catalytic Converter Performance of single-wall Carbon Nanotubes Doped with Titanium." Journal of Inorganic and Organometallic Polymers and Materials 35, no. 6 (2025): 4511-4524.
[3] Soham, P., B. Sapanakharat, and K. Ajinkya. “Modification of Catalytic Converters Thereby Bettering Their Performance and Reducing the Cost.” National Conference on Emerging Trends in Science and Technology (2018): 45–50.
[4] Kalam, M. A., H. H. Masjuki, Mohd Redzuan, T. M. I. Mahlia, M. A. Fuad, M. Mohibah, K. H. Halim et al. "Development and test of a new catalytic converter for natural gas fuelled engine." Sadhana 34, no. 3 (2009): 467-481.
[5] Hashemi Darian, J. Selection of the Optimal Catalytic Converter for Spark Ignition Engines Based on Engine Performance and Emission Conditions. Master’s thesis, Department of Mechanical Engineering, Automotive Powertrain, K. N. Toosi University of Technology, 2018. Supervisor: Amir Hossein Shamkhi. (in Persian).
[6] Lee, Seokhwan, Choongsik Bae, Yongpyo Lee, and Taesik Han. "Effects of engine operating conditions on catalytic converter temperature in an SI engine." In International Spring Fuels & Lubricants Meeting & Exhibition. 2002.
[7] Tyagi, R., and R. Ranjan. “Effect of Heating the Catalytic Converter on Emission Characteristic of Gasoline Automotive Vehicles.” International Journal of Ambient Energy (2002): 1–7.
[8] Zuo, Q., Y. Xie, and Q. Guan. “Effect of Critical Dual-Carrier Structure Parameters on Performance Enhancement of a Dual-Carrier Catalytic Converter and the Gasoline Engine System.” Energy Conversion and Management (2019): 1–18.
[9] Hajimirzaee, S., and A. Doyle. “3D-Printed Catalytic Converters with Enhanced Activity for Low-Temperature Methane Oxidation in Dual-Fuel Engines.” Fuel 274 (2020): 1–11
[10] Mohallem, Nelcy Della Santina, Marcelo Machado Viana, and Ronald A. Silva. "Automotive catalysts: performance, characterization and development." New trends and developments in automotive industry (2011): 347-364.
[11] Thakur, Arpit, Ashish Sharma, Rajeev Kumar, Shubham Sharma, Nagaraj Patil, Sumit Kanchan, VK Bupesh Raja, Abinash Mahapatro, Deepak Gupta, and Ehab El Sayed Massoud. "Numerical study of catalytic converter geometries and their impact on exhaust back pressure and energy conversion in engine exhaust systems using parametric simulation: insights into non-equilibrium thermodynamics." International Journal of Chemical Reactor Engineering 23, no. 1 (2025): 61-76.
[12] Huu-Quan, Do, Ali Mohammad Rostami, Mozafar Shokri Rad, Mohsen Izadi, Ahmad Hajjar, and Qingang Xiong. "3D numerical investigation of turbulent forced convection in a double-pipe heat exchanger with flat inner pipe." Applied Thermal Engineering 182 (2021): 116106.
[13] Mokhtari, A., and M. Saadat. "Light-Off Temperatures and Conversion Efficiency Analysis in Catalytic Converters: A Numerical Modeling Approach." Iranica Journal of Energy and Environment 16, no. 4 (2025): 706-719.
[14] Buruiana, Daniela Laura, Adrian Sachelarie, Claudiu Butnaru, and Viorica Ghisman. “Important Contributions to Reducing Nitrogen Oxide Emissions from Internal Combustion Engines.” International Journal of Environmental Research (2021).
[15] Ghazikhani, M., and M. Hatami. “Exergy Recovery from the Exhaust Cooling in a DI Diesel Engine for BSFC Reduction Purposes.” Energy (2013): 1–8
 
Volume 24, Issue 3 - Serial Number 86
In Progress
Autumn 2026
Pages 31-43

  • Receive Date 03 December 2024
  • Revise Date 22 July 2025
  • Accept Date 15 November 2025